汽車發生故障是家常便飯的事情，大部分人都會選擇送去修理廠進行修理檢查，但是修理廠檢查一個很麻煩，而且費用也不便宜，所以車主自己看懂一些常見故障和更換小配件，也是能在緊急情況下解決很多事情的。汽車常見故障如何診斷呢？下面
濟南奧迪汽車保養人員就來講講車輛安全檢查方法吧。
It's a common thing for a car to break down. Most people choose to send it to the repair shop for repair and inspection. However, the repair shop is very troublesome and the cost is not cheap. Therefore, the car owner can understand some common faults and replace small parts, and can solve many problems in an emergency. How to diagnose common automobile faults? Let's talk about the vehicle safety inspection methods by Audi maintenance personnel in Jinan.
汽車外觀
Car appearance
注意車身是否整潔、周正，有無明顯銹跡和變形；2、檢查左右后視鏡、內后視鏡，應完好、無損毀；3、檢查刮水器各擋位是否工作正常；4、檢查發動機、水箱，是否有漏油、漏液現象。
Pay attention to whether the vehicle body is clean and upright, and whether there is obvious rust and deformation; 2. Check the left and right rear-view mirrors and internal rear-view mirrors, which shall be intact and free of damage; 3. Check whether each gear of the wiper works normally; 4. Check the engine and water tank for oil and liquid leakage.
制動系統
braking system
檢查各車輪制動氣室、及制動管路的密封性；2、檢查氣壓表的系統壓力是否正常；3、檢查制動系統各故障指示燈指示狀況是否存在故障；4、檢查并指壓空氣壓縮機傳動帶，是否存在有龜裂的現象。
Check the tightness of brake air chamber and brake pipeline of each wheel; 2. Check whether the system pressure of the barometer is normal; 3. Check whether there is any fault in the indication condition of each fault indicator lamp of the braking system; 4. Check and press the air compressor drive belt for cracks.
轉向系統
steering system
檢查轉向盤各連接處是夠有松曠、開裂的現象。
Check whether the joints of the steering wheel are loose and cracked.
轉動系統
Rotating system
檢查傳動軸支架，是否存在有破損和變形的現象；2、檢查自動變速器、液力緩速器的密封狀況。
Check the transmission shaft bracket for damage and deformation; 2. Check the sealing condition of automatic transmission and hydraulic retarder.
照明、信號燈
Lighting and signal lamp
前照燈應齊全、完好、表面清沽；2、檢查信號指示燈的表面是否干凈，且工作是否正常。
The headlamp shall be complete and intact, with clear surface; 2. Check whether the surface of the signal indicator is clean and works normally.
輪胎
tyre
檢查輪胎外觀是否有破裂、凸起、異物刺入等現象；2、檢查輪胎磨損情況；3、檢查輪胎規格和花紋是否一致；4、檢查輪胎的氣壓是否正常。
Check the appearance of the tire for cracks, protrusions, penetration of foreign matters, etc; 2. Check the tire wear; 3. Check whether the tire specification and tread pattern are consistent; 4. Check whether the tire pressure is normal.
懸架系統
suspension system
檢查懸架的彈性元件，是否牢固，有無斷裂等情況；2、檢查鋼板彈簧各部分的零件是否齊全。
Check whether the elastic elements of the suspension are firm and broken; 2. Check whether all parts of the leaf spring are complete.
安全設施
Safety facilities
檢查動力啟閉車門的機件是否完整；2、檢查安全頂窗，安全頂窗機件還否齊全、完好。3、檢查安全錘、滅火器是否在指定的位置。
Check whether the mechanical parts of the power door are complete; 2. Check whether the safety top window and its components are complete and intact. 3. Check whether the safety hammer and fire extinguisher are in the designated position.
攝像頭行車記錄儀
Camera dash cam
檢查車內攝像頭，攝像頭的拍攝方向應符合規定且無遮擋。
Check the camera in the vehicle, and the shooting direction of the camera shall meet the requirements and be free of obstruction.
This is the general description of the vehicle safety inspection method. If you want to use it smoothly for a long time, you need to do more inspections and regular maintenance. You can visit our website for more information http://www.nanofluidizer.com consulting service
